Repair Drywall and Eliminate Nail Pops
First, the very best method to correct your existing nail pops is to be sure that the top of the nail or screw is recessed about 1/32 inch. If it is sticking up, do not drive it too deep or you will break through the paper surface. If you do, the drywall is going to be severely weakened.
Next spread a little spackling compound within the nail pop area. Allow it to dry and then sand it down. Lay a direct edge over it to be sure that it's not too high. A slightly raised spot surpasses making it too shallow. Allow it to dry thoroughly because the compound will shrink a little.
Paint the repaired area with drywall primer. Paint a place larger compared to fixed spot so your larger area will absorb the finished coat uniformly. This will ensure it is extremely difficult to detect that the repair was made to the wall.
The problem of nail pops can be due to either improper drywall installation procedures by your builder or by damp lumber. Although lumber is supposedly kiln-dried, it can pick up moisture as time passes, especially if it's been out in the rain for a while.
Wall studs, that the drywall is nailed or screwed to, shrink while they dry drywall repair. Unfortunately, they shrink the greatest amount (due to the orientation of the grain) in its depth dimension (nominal 4 inches).
If the drywall is nailed against damp wall studs and the studs shrink just a little while they dry, a little gap could form between the drywall and the stud. It doesn't take much. If the drywall is bumped and pushed back against the stud, the nail head causes it to pop.
The best approach to minimize nail pops is to use properly dried lumber. As your project is just a room addition, store the lumber in your garage, from the rain, until it's used. If possible delay your construction until the weather is reasonably warm, however not during high humidity months.
Inspect the lumber as each piece can be used because alignment of the lumber is very important to be sure that the drywall makes good experience of it. Your builder may use any bowed studs in areas so it is not wasted.
Make sure proper drywall nails and screws are employed and they're of the proper length. They are unique of ordinary fasteners. Drywall fasteners have specially shaped heads so that they do not tear the paper when they're recessed. For 1/2-inch drywall, 1 1/4-inch angular ring shanked drywall nails work well.
If possible, have your builder wait a while to set up the drywall following the wall framing is complete and the area is closed in. The longer you are able to wait, the better it is. This allows time for the framing lumber to dry and for the moisture content of all of the pieces to stabilize.
The spacing of the screws and nails is equally crucial that you minimize future nail pops and other problems. The maximum spacing for fasteners on drywall employed for the ceiling is 12 inches on centers. Which means a four--foot wide panel must have at the very least five fasteners. For wall panels, the fasteners can be 16 inches on centers.
Next spread a little spackling compound within the nail pop area. Allow it to dry and then sand it down. Lay a direct edge over it to be sure that it's not too high. A slightly raised spot surpasses making it too shallow. Allow it to dry thoroughly because the compound will shrink a little.
Paint the repaired area with drywall primer. Paint a place larger compared to fixed spot so your larger area will absorb the finished coat uniformly. This will ensure it is extremely difficult to detect that the repair was made to the wall.
The problem of nail pops can be due to either improper drywall installation procedures by your builder or by damp lumber. Although lumber is supposedly kiln-dried, it can pick up moisture as time passes, especially if it's been out in the rain for a while.
Wall studs, that the drywall is nailed or screwed to, shrink while they dry drywall repair. Unfortunately, they shrink the greatest amount (due to the orientation of the grain) in its depth dimension (nominal 4 inches).
If the drywall is nailed against damp wall studs and the studs shrink just a little while they dry, a little gap could form between the drywall and the stud. It doesn't take much. If the drywall is bumped and pushed back against the stud, the nail head causes it to pop.
The best approach to minimize nail pops is to use properly dried lumber. As your project is just a room addition, store the lumber in your garage, from the rain, until it's used. If possible delay your construction until the weather is reasonably warm, however not during high humidity months.
Inspect the lumber as each piece can be used because alignment of the lumber is very important to be sure that the drywall makes good experience of it. Your builder may use any bowed studs in areas so it is not wasted.
Make sure proper drywall nails and screws are employed and they're of the proper length. They are unique of ordinary fasteners. Drywall fasteners have specially shaped heads so that they do not tear the paper when they're recessed. For 1/2-inch drywall, 1 1/4-inch angular ring shanked drywall nails work well.
If possible, have your builder wait a while to set up the drywall following the wall framing is complete and the area is closed in. The longer you are able to wait, the better it is. This allows time for the framing lumber to dry and for the moisture content of all of the pieces to stabilize.
The spacing of the screws and nails is equally crucial that you minimize future nail pops and other problems. The maximum spacing for fasteners on drywall employed for the ceiling is 12 inches on centers. Which means a four--foot wide panel must have at the very least five fasteners. For wall panels, the fasteners can be 16 inches on centers.
.
Comments
Post a Comment